Warning

This version of the documentation is NOT an official release. You are looking at ‘latest’, which is in active and ongoing development. You can change versions on the bottom left of the screen.

Tsodyks depressing example

This scripts simulates two neurons. One is driven with dc-input and connected to the other one with a depressing Tsodyks synapse. The membrane potential trace of the second neuron is recorded.

This example reproduces Figure 1A of 1. This example is analog to tsodyks_facilitating.py, except that different synapse parameters are used. Here, a large facilitation parameter U causes a fast saturation of the synaptic efficacy (Eq. 2.2), disabling a facilitating behavior.

References

1

Tsodyks M, Pawelzik K, Markram H (1998). Neural networks with dynamic synapses. Neural computation, http://dx.doi.org/10.1162/089976698300017502

See Also

Tsodyks facilitating example

First, we import all necessary modules for simulation and plotting.

import nest
import nest.voltage_trace
import matplotlib.pyplot as plt
from numpy import exp

Second, the simulation parameters are assigned to variables. The neuron and synapse parameters are stored into a dictionary.

resolution = 0.1    # simulation step size (ms)
Tau = 40.0          # membrane time constant
Theta = 15.0        # threshold
E_L = 0.0           # reset potential of membrane potential
R = 0.1             # 100 M Ohm
C = Tau / R         # Tau (ms)/R in NEST units
TauR = 2.0          # refractory time
Tau_psc = 3.0       # time constant of PSC (= Tau_inact)
Tau_rec = 800.0     # recovery time
Tau_fac = 0.0       # facilitation time
U = 0.5             # facilitation parameter U
A = 250.0           # PSC weight in pA
f = 20.0 / 1000.0   # frequency in Hz converted to 1/ms
Tend = 1200.0       # simulation time
TIstart = 50.0      # start time of dc
TIend = 1050.0      # end time of dc
I0 = Theta * C / Tau / (1 - exp(-(1 / f - TauR) / Tau))  # dc amplitude

neuron_param = {"tau_m": Tau,
                "t_ref": TauR,
                "tau_syn_ex": Tau_psc,
                "tau_syn_in": Tau_psc,
                "C_m": C,
                "V_reset": E_L,
                "E_L": E_L,
                "V_m": E_L,
                "V_th": Theta}

syn_param = {"tau_psc": Tau_psc,
             "tau_rec": Tau_rec,
             "tau_fac": Tau_fac,
             "U": U,
             "delay": 0.1,
             "weight": A,
             "u": 0.0,
             "x": 1.0}

Third, we reset the kernel and set the resolution using the corresponding kernel attribute.

nest.ResetKernel()
nest.resolution = resolution

Fourth, the nodes are created using Create. We store the returned handles in variables for later reference.

neurons = nest.Create("iaf_psc_exp", 2)
dc_gen = nest.Create("dc_generator")
volts = nest.Create("voltmeter")

Fifth, the iaf_psc_exp neurons, the dc_generator and the voltmeter are configured using SetStatus, which expects a list of node handles and a parameter dictionary or a list of parameter dictionaries.

neurons.set(neuron_param)
dc_gen.set(amplitude=I0, start=TIstart, stop=TIend)
volts.set(label="voltmeter", interval=1.)

Sixth, the dc_generator is connected to the first neuron (neurons[0]) and the voltmeter is connected to the second neuron (neurons[1]). The command Connect has different variants. Plain Connect just takes the handles of pre- and postsynaptic nodes and uses the default values for weight and delay. Note that the connection direction for the voltmeter reflects the signal flow in the simulation kernel, because it observes the neuron instead of receiving events from it.

nest.Connect(dc_gen, neurons[0])
nest.Connect(volts, neurons[1])

Seventh, the first neuron (neurons[0]) is connected to the second neuron (neurons[1]). The command CopyModel copies the tsodyks_synapse model to the new name syn with parameters syn_param. The manually defined model syn is used in the connection routine via the syn_spec parameter.

nest.CopyModel("tsodyks_synapse", "syn", syn_param)
nest.Connect(neurons[0], neurons[1], syn_spec="syn")

Finally, we simulate the configuration using the command Simulate, where the simulation time Tend is passed as the argument. We plot the target neuron’s membrane potential as a function of time.

nest.Simulate(Tend)
nest.voltage_trace.from_device(volts)
plt.show()

Total running time of the script: ( 0 minutes 0.000 seconds)

Gallery generated by Sphinx-Gallery